Puppy Love - Transfers w/ Matching Clay Cutter
Choose from the set of transfers and matching cutter, or purchase single transfer sheets. ***Cutter info :
1.25” tall Puppy Outline Cutter.
3D Printed with PLA+
.4mm cutting edge for clean cuts and sturdy cutter.
Food safe.
*TIPS: To keep clay from sticking and get a clean edge, dip in cornstarch or water before cutting clay. I recommend rolling clay onto a slick surface like a tile so that the clay will stick to the tile and not lift off when you cut into it. To clean cutters, use warm soapy water. Do not wash in dishwasher.
***Transfer Info :
This set includes 2 sheets with 9 images each. That totals to be enough images to create 9 pair of earrings.
This product and is so versatile and fun! You can use these sheets to transfer the image to your clay before cutting and baking for unique designs!
Each sheet is approximately 4”x5”
HOW TO USE:
Start with a light color clay such and white or cream.
Trim your the desired size of transfer paper for your project. Make sure that your clay slab is a bit bigger than your transfer to ensure that all edges of the transfer are stuck down and won’t lift up.
Place the transfer face down on the clay and smooth over it to make sure there are no air bubbles.
Use a wet paper towel to moisten the back of the transfer. Let it set for 30-45 seconds. You’ll know that it’s ready when you see it start to slide. Gently slide it away to avoid lifting and getting air bubbles.
Allow the transfer to dry for a couple of minute and then use your favorite clay cutters! *Embossed cutters can cause breaks in the design and lifting so I suggest using outline cutters for the best results.
Bake as normal and seal the transfer. I suggest using UV resin. **You can use Duraclear sealant, but make sure the initial coat is thin and that you coat it quickly with minimal brush strokes to avoid ink bleeds and smears. If you have any further questions please feel free to contact me!
Choose from the set of transfers and matching cutter, or purchase single transfer sheets. ***Cutter info :
1.25” tall Puppy Outline Cutter.
3D Printed with PLA+
.4mm cutting edge for clean cuts and sturdy cutter.
Food safe.
*TIPS: To keep clay from sticking and get a clean edge, dip in cornstarch or water before cutting clay. I recommend rolling clay onto a slick surface like a tile so that the clay will stick to the tile and not lift off when you cut into it. To clean cutters, use warm soapy water. Do not wash in dishwasher.
***Transfer Info :
This set includes 2 sheets with 9 images each. That totals to be enough images to create 9 pair of earrings.
This product and is so versatile and fun! You can use these sheets to transfer the image to your clay before cutting and baking for unique designs!
Each sheet is approximately 4”x5”
HOW TO USE:
Start with a light color clay such and white or cream.
Trim your the desired size of transfer paper for your project. Make sure that your clay slab is a bit bigger than your transfer to ensure that all edges of the transfer are stuck down and won’t lift up.
Place the transfer face down on the clay and smooth over it to make sure there are no air bubbles.
Use a wet paper towel to moisten the back of the transfer. Let it set for 30-45 seconds. You’ll know that it’s ready when you see it start to slide. Gently slide it away to avoid lifting and getting air bubbles.
Allow the transfer to dry for a couple of minute and then use your favorite clay cutters! *Embossed cutters can cause breaks in the design and lifting so I suggest using outline cutters for the best results.
Bake as normal and seal the transfer. I suggest using UV resin. **You can use Duraclear sealant, but make sure the initial coat is thin and that you coat it quickly with minimal brush strokes to avoid ink bleeds and smears. If you have any further questions please feel free to contact me!
Choose from the set of transfers and matching cutter, or purchase single transfer sheets. ***Cutter info :
1.25” tall Puppy Outline Cutter.
3D Printed with PLA+
.4mm cutting edge for clean cuts and sturdy cutter.
Food safe.
*TIPS: To keep clay from sticking and get a clean edge, dip in cornstarch or water before cutting clay. I recommend rolling clay onto a slick surface like a tile so that the clay will stick to the tile and not lift off when you cut into it. To clean cutters, use warm soapy water. Do not wash in dishwasher.
***Transfer Info :
This set includes 2 sheets with 9 images each. That totals to be enough images to create 9 pair of earrings.
This product and is so versatile and fun! You can use these sheets to transfer the image to your clay before cutting and baking for unique designs!
Each sheet is approximately 4”x5”
HOW TO USE:
Start with a light color clay such and white or cream.
Trim your the desired size of transfer paper for your project. Make sure that your clay slab is a bit bigger than your transfer to ensure that all edges of the transfer are stuck down and won’t lift up.
Place the transfer face down on the clay and smooth over it to make sure there are no air bubbles.
Use a wet paper towel to moisten the back of the transfer. Let it set for 30-45 seconds. You’ll know that it’s ready when you see it start to slide. Gently slide it away to avoid lifting and getting air bubbles.
Allow the transfer to dry for a couple of minute and then use your favorite clay cutters! *Embossed cutters can cause breaks in the design and lifting so I suggest using outline cutters for the best results.
Bake as normal and seal the transfer. I suggest using UV resin. **You can use Duraclear sealant, but make sure the initial coat is thin and that you coat it quickly with minimal brush strokes to avoid ink bleeds and smears. If you have any further questions please feel free to contact me!